Land Rover Discovery Owners & Service Manuals

Land Rover Discovery: General warning/ information message (amber)

Land Rover Discovery (2009–2016) Owner's Manual / Warning lamps / General warning/ information message (amber)

Illuminates when a non-critical warning message or an information message is available in the Message centre.

GLOW PLUGS (AMBER)

Illuminates when the ignition is switched on, to indicate that the glow plugs are active.

LOW FUEL WARNING (AMBER)

Illuminates when the fuel level is low. Refuel at the earliest opportunity.

The arrow shows which side of the vehicle to locate the fuel filler flap.

PROGRESS CONTROL SYSTEM (AMBER)

Illuminates to confirm that the Progress control system is enabled.

REAR FOG LAMP (AMBER)

Illuminates when the rear fog lamps are switched on.

TYRE PRESSURE MONITORING SYSTEM (YELLOW)

The warning lamp illuminates, accompanied by a message in the Message centre, to warn that 1 or more tyres are significantly under-inflated.

Stop the vehicle as soon as possible, check the tyre pressures and inflate to the recommended pressure.

The lamp will flash to indicate a system fault.

AUTO HIGH BEAM (GREEN)

Illuminates when the Auto high beam feature has switched on the high beam headlamps.

CRUISE CONTROL (GREEN)

Illuminates when Cruise control or Adaptive Cruise Control (ACC) is active.

DIRECTION INDICATORS (GREEN)

The appropriate warning lamp will flash when the direction indicators are operated.

FORWARD ALERT (GREEN)

Illuminates when Forward alert is active.

FRONT FOG LAMPS (GREEN)

Illuminates when the front fog lamps are switched on.

GEAR SHIFT (GREEN)

The gear shift indicator illuminates briefly at the recommended gear change point (up-shift).

The shift indicator will not illuminate while Cruise control is active and not being overridden by pressing the throttle pedal.

Note: This warning indicator is only a guide. It remains the responsibility of the driver to operate the vehicle in an appropriate manner for the prevailing conditions.

HILL DESCENT CONTROL (GREEN)

Illuminates continuously when Hill Descent Control (HDC) is selected and HDC operating conditions are met.

If the lamp flashes, HDC has been selected, but the operating conditions are not being met or HDC fade-out is occurring.

INTELLIGENT STOP/START (GREEN)

Illuminates when the engine is shut down by the Intelligent stop/start system.

Note: Other warnings normally associated with an engine shutdown, for example, the ignition warning lamp, do not illuminate during an engine shutdown by the Intelligent stop/start system.

LANE DEPARTURE WARNING (GREEN)

Recognised lane markings will illuminate green, otherwise they will illuminate grey. The lamp Illuminates grey to confirm the Lane Departure Warning (LDW) system is enabled.

SIDE LAMPS (GREEN)

Illuminates when the side lamps are switched on.

TRAILER DIRECTION INDICATORS (GREEN)

Illuminates as a bulb check when the ignition is switched on and extinguishes when the engine is started.

If a trailer is attached, the warning lamp will flash in conjunction with the direction indicator warning lamp. If the lamp fails to flash, the direction indicator bulb on the trailer may be faulty.

Note: If the attached and connected trailer is fitted with LED lights, the bulb check may not be performed.

HIGH BEAM (BLUE)

Illuminates when the high beam headlamps are switched on or flashed.

FOLLOW MODE OFF (GREY)

Illuminates when the Adaptive Cruise Control (ACC) system is disabled.

    READ NEXT:

     Exterior lights

     Lighting control

    With the headlamps on, push the control away from the steering wheel to select high beam. The Instrument panel warning lamp will illuminate. Note: Do not use high beam where it may distract ot

     Headlamp courtesy delay

    This feature operates whenever the lighting control is in the auto position and the ignition is switched off. The headlamps will remain illuminated for up to 240 seconds. Note: The time delay may be c

    SEE MORE:

     Door Window Motor Initialization

    NOTES: Make sure that the vehicle battery is fully charged before carrying out this procedure. After the battery has been disconnected or a new window regulator and motor or door module has been installed, it is necessary to initialize each door window motor separately to operate the onetouch

     Manual Transmission Transaxle External Controls Gearshift Cables (G1779360) / Removal and Installation

    REMOVAL NOTES: Removal steps in this procedure may contain installation details. Some variation in the illustrations may occur, but the essential information is always correct. Refer to: Air Cleaner (303-12, Removal and Installation). NOTE: Neutral must be selected before the cables are release

    © 2019-2024 Copyright www.lrdisc.com